33问: 你们的热转印纸在纯棉T恤上印,可以吗?
Is it ok for cotton t-shirt with your heat transfer paper?
A: 可以的.只要是耐高温的布料都可以使用我们的产品.
Yes, it is ok for any fabrics which can resist high temperature.
34、Q: 我们的热转印纸需要温度和时间是多少?
What is the temperature and when does it need about our heat transfer paper?
A: 每一种产品都有他们的使用方式,不同产品需要不同的温度和时间. 浅色转印纸需要185度，时间15秒。
深色转印纸需要165度，时间25秒。
Different products have their directions. So the temperatures and times are different. For light heat transfer paper, it needs 185oC, and 15seconds. For dark heat transfer paper, it needs 165oC, by 25seconds
35、Q: 是否直接用普通的墨水打印?连供墨水的打印机也可以吗？热升华墨水呢？
Is it printed by normal inks? What about CISS inks and sublimation?
A: 是的. 并不需要特殊的打印机和墨水,只要用办公室的打印机就可以使用我们的产品.
Yes, we do not need special printer and inks. You can use the inkjet printer and inks in your office, and then print our inkjet heat transfer paper. It is no problem to use CISS inks, sublimation inks and any other inks.
36、Q:普通打印机的墨水打印,会不会褪色?
Is it fade when we use inkjet printer?
A: 不会的.我们的产品都有经过水洗测试.至少能通过机洗60次以上.
No, it is difficult to fade. Our products have been proved that you can wash your t-shirt above 60times by washing machine.
37、Q:烫画机的压力调到多大比较合适?
What is the pressure of press machine?
A: 中等压力或超大压力.
Moderate or high pressure.
38、Q：打印后，怎么会溢墨?
Why is it spilled inks when it was printed?
A：打印时,设墨墨量为最小,选择”照片”模式打印,而不是”文件”
We should set the printer on Mini amount of ink when printing. We set “quality option” on “Photo”,but not “draft” about your inkjet printer.
39、Q: 深色的纸为什么会泛白?
Why does the whitening phenomenon occurs on dark inkjet transfer paper?
A: 有这么几种情况:a,温度过高,降低温度;b,时间过长,缩短时间;c,在防油纸的上面没有放一块棉布，请加一层棉布料
These situations can occur to whitening phenomenon: a.the temperature is high, please down the temperature;
b.the time is too long ,please use less time;c. you do not put a cotton on the grease proof paper,please do it.
40、Q:HT-150R 撕不下来?
Why can not been peeled off about HT-150R?
A:一定要烫完后 应立即趁热把背纸撕下来,时间不能等冷了再撕,所以速度要快.
It should peel the back paper off with hot. You can not peel it off when the paper is cold ,so please quickly.
41、Q: HT-150R 将背纸撕下来后,为什么会起毛?
When peel the back paper of HT-150R, why is it pilling?
A: 有2种方法可以解决.1.温度不够,适当调高温度 2.烫完后，要趁热把背纸撕下，不能等冷了再撕3.起毛的地方用防油纸覆盖,再压烫一次
You can do these ways to solve it: 1.the temperature is low, please adjust proper temperature on the heat press machine 2.do not peel the back paper off when it is cold, please take it off with hot.3 put the grease proof paper on the pattern, and then use the press machine to transfer it again.
42、Q:HT-150印烫后,背纸怎么起泡了?
Why does the back paper have bubble with HT-150?
A:温度过高,在烫印之前,加一张防油纸在HT-150背纸上隔热.
The temperature is too high, please take a grease proof paper on the HT-150.
43、Q: 如果第１次没有烫不牢，能不能用烫画机第２次烫印？
If it is not stable at first, should we use the heat press machine again?
Ａ：可以的。在烫不牢的情况下，铺上防油纸后，再重新压烫，这样图案就不易脱落，更加牢固。
Yes, it is ok. if you find the image out of the fabric, please put a grease proof paper on the image, and then set heat press machine on 160OC , by 10seconds to transfer it again.
44、Ｑ：烫画的衣服洗涤后能用电熨斗的蒸气熨平吗？
Should we use the house iron with steam to iron the fabric which is finished transferring image after be washed?
Ａ：图片烫印完成后，可以使用电熨斗，但不可以用蒸气档.你需要把防油纸或棉布放在图案上面后，再熨平衣服。
You can use house iron after finishing transfer,but do not use the steam function. You need to put the proof grease paper or a piece of cotton cover the image ,and the iron the fabric.
44、Q: 为什么转印的时候老是一个地方烫印不好，而且会起皮，但是其它地方都很好?
Why does it good most parts of heat transfer paper, but some part is bad and it is pilling.
A:放烫画机的地方不平，导致转印的时候受力不均衡，最后的结果是一部分烫印效果好，一部分比较差。
烫印的时候需要一个平整的地方，这样出来的效果才会更好。
The place which is the heat press machine on is not formation, causing the uneven distribution when we are transferring. We need a stable ,heat-resistant surface for more better effect.
45、Q: 我们的热转印纸是不是可以用熨斗烫？那烫的时候需要多少时间，压力要多大？
Is it ok for your products by house iron What is the time should we take? How pressure should we need ?
A: 是的，我们的转印纸可以用电熨斗。烫的时候，需要用大力气烫1分钟左右。
Yes, our heat transfer paper is ok for house iron. It needs more pressure as you can for one minute.
46、Q: 激光转印纸图案被粘坏了：
Laser heat transfer paper surface image is broken ，
A: 有3种可能性：1、激光机打印时选的纸张进纸厚度，选太薄了，解决办法：请客户进纸厚度，选择较厚这一栏
1: Setting printing paper thickness is too thin
Solve methods: Before printing you should choose the thick paper in the laser printer
47、Q:激光机刚加热时，机身内温度较高，可达到200度-300度，解决办法：建议客户先用普通纸过一下机子，让机身内温度稳定一点再用转印纸打印，因为转印纸面层有胶，胶的溶点在165度。
2: The color laser printer temperature is high when the laser heating, it will reach on 200-300degree
Solve methods: suggest use the normal A4 white paper pass the color laser printer in the heating
After the heater is steady, you can printing the heat transfer paper, the paper surface is PU .The Melting temperature is 165degree
48、Q:激光机内的搓纸头上有残渣，残渣部份会粘住激光纸的面层，导致转印纸图案部份被粘住移位脱落在激光机搓纸头上。
A：用酒精或专用清洁液清洁一下激光机的搓纸头，清洁完用普通纸先过一下机子。
Q: In the laser printer, the Pickup head leave some dirty and broken image, so after printing，the dirty broken image will put on the surface laser paper
A: Solve methods: cleaning the pickup head by alcohol or a special cleaner,
After finish cleaning, use the normal paper pass the printer firstly.
49、Q：我用你们的HT-150R浅色热撕，怎么底纸上还有残留图案？
A: 您用的是不是热升华墨水，使用热升华墨水会导致四分之三的图案转入图层中，还有的一部分留在底纸上。而且升华墨水易拉丝。
Post time: Sep-11-2021
